
One fitment. Four brands. The 66.6mm hub bore is shared across BMW G-series, Audi, Mercedes-Benz, and Porsche Macan platforms — all running a 5x112 bolt pattern. Available in 5mm through 25mm, with the correct hardware for each size: extended wheel bolts matched to your vehicle and spacer thickness up to 20mm, and mounting bolts with the 25mm.
Specifications
- Bolt Pattern: 5x112
- Hub Bore: 66.6mm
- Thickness: 5mm, 8mm, 10mm Flat, 10mm Hub Centric, 12.5mm, 15mm, 18mm, 20mm, 25mm
- Thread Pitch: 14x1.25 (BMW) Conical Seat | 14x1.5 (Audi / Mercedes / Porsche) Ball Seat
- Material: Billet Aluminum T6061, Grade 10.9 Steel Hardware as standard (see bolt chart)
-
Type:
- SPS Series, Slip On, Flat (no lip) (5mm, 8mm, 10mm)
- SPS Series, Slip On, Hub Centric: (10mm - 20mm)
- SPA Series, Bolt On: (25mm)
Fitment
BMW G20/G30/G01/G05/G06 (2017+) — Audi A4, A5, A6, Q5, Q7 (66.5/66.6mm CB) — Mercedes-Benz C-Class, E-Class, GLC, S-Class — Porsche Macan. Enter your vehicle for automatic bolt selection.
Kit Includes
- (2) Wheel Spacers
- (10) Extended Wheel Bolts — seat type and length matched to your vehicle and spacer size
- 25mm kit: (2) Wheel Spacers and (10) 14x1.5 Mounting Bolts
Included wheel bolts by spacer size
| Spacer | Bolt Length | Grade / Finish |
|---|---|---|
| 5mm | 32mm | 12.9 Black |
| 8mm | 35mm | 10.9 Chrome |
| 10mm Flat or Hub Centric | 40mm | 10.9 Chrome |
| 12.5mm | 40mm | 10.9 Chrome |
| 15mm | 40mm | 10.9 Chrome |
| 18mm | 45mm | 10.9 Chrome |
| 20mm | 45mm | 10.9 Chrome |
| 25mm | Bolt-on, (10) 14x1.5 mounting bolts | |
Grade 12.9 Black bolts are available as a paid upgrade on 8–20mm.
BMW vehicles with the 25mm: BMW 5x112 models use 14x1.25 wheel bolts. Use your factory wheel bolts to fix the spacer to the hub, and the included 14x1.5 bolts to secure the wheel to the spacer.
Hub Lip Guide
Hub lip height varies by make, model, year and axle, and we can't confirm every vehicle. Measure your factory hub lip front and rear, from the hub face to the end of the lip, ideally with calipers. If a spacer doesn't sit flush against the hub, do not install it.
- 5mm, 8mm and 10mm Flat: These have no recess and slide over your factory hub lip. The 10mm Flat is not fully hub centric.
- 10mm Hub Centric, check your wheels before ordering: This spacer has a 5mm x 5mm chamfer at the base of its hub lip, where the wheel sits. Your wheel needs at least a 5mm chamfer around the back of its center bore to sit flush. Not all wheels have this.
- 12.5mm Hub Centric, check fitment before ordering: This spacer fits factory hub lips up to 12.5mm. If your hub lip is taller than 12.5mm, this spacer will not sit flush against the hub. It has a smaller 3mm chamfer, which suits most factory and aftermarket wheels.
Some vehicles on this fitment have been reported with hub lips over 13mm, so measure even if you're ordering a thicker spacer.
Modifying the hub: A Hub Centric spacer can only be used on a taller hub lip if the lip is ground or filed down until the spacer sits flush against the hub. This permanently modifies a factory part and is done at your own risk, so we only suggest it if absolutely necessary.
Fitment, installation and road use
Confirm compatibility with your vehicle, wheels and hardware before installation. Vehicle fitment results do not establish clearance for every wheel setup or confirm road-use legality.
Incorrect fitment, installation or maintenance can cause wheel separation, loss of control, serious injury or death. Follow the applicable installation and inspection instructions. Professional installation is recommended.
Road-use and inspection requirements vary by jurisdiction. Confirm local requirements before purchasing.
One fitment. Four brands. The 66.6mm hub bore is shared across BMW G-series, Audi, Mercedes-Benz, and Porsche Macan platforms — all running a 5x112 bolt pattern. Available in 5mm through 25mm, with the correct hardware for each size: extended wheel bolts matched to your vehicle and spacer thickness up to 20mm, and mounting bolts with the 25mm.
Specifications
- Bolt Pattern 5x112
- Hub Bore 66.6mm
- Thickness 5mm, 8mm, 10mm Flat, 10mm Hub Centric, 12.5mm, 15mm, 18mm, 20mm, 25mm
- Thread Pitch 14x1.25 (BMW) Conical Seat | 14x1.5 (Audi / Mercedes / Porsche) Ball Seat
- Material Billet Aluminum T6061, Grade 10.9 Steel Hardware as standard (see bolt chart)
-
Type
- SPS Series, Slip On, Flat (no lip) (5mm, 8mm, 10mm)
- SPS Series, Slip On, Hub Centric: (10mm - 20mm)
- SPA Series, Bolt On: (25mm)
- (2) Wheel Spacers
- (10) Extended Wheel Bolts — seat type and length matched to your vehicle and spacer size
- 25mm kit: (2) Wheel Spacers and (10) 14x1.5 Mounting Bolts
Included wheel bolts by spacer size
| Spacer | Bolt Length | Grade / Finish |
|---|---|---|
| 5mm | 32mm | 12.9 Black |
| 8mm | 35mm | 10.9 Chrome |
| 10mm Flat or Hub Centric | 40mm | 10.9 Chrome |
| 12.5mm | 40mm | 10.9 Chrome |
| 15mm | 40mm | 10.9 Chrome |
| 18mm | 45mm | 10.9 Chrome |
| 20mm | 45mm | 10.9 Chrome |
| 25mm | Bolt-on, (10) 14x1.5 mounting bolts | |
Grade 12.9 Black bolts are available as a paid upgrade on 8–20mm.
BMW vehicles with the 25mm: BMW 5x112 models use 14x1.25 wheel bolts. Use your factory wheel bolts to fix the spacer to the hub, and the included 14x1.5 bolts to secure the wheel to the spacer.
BMW G20/G30/G01/G05/G06 (2017+) — Audi A4, A5, A6, Q5, Q7 (66.5/66.6mm CB) — Mercedes-Benz C-Class, E-Class, GLC, S-Class — Porsche Macan. Enter your vehicle for automatic bolt selection.
Hub lip height varies by make, model, year and axle, and we can't confirm every vehicle. Measure your factory hub lip front and rear, from the hub face to the end of the lip, ideally with calipers. If a spacer doesn't sit flush against the hub, do not install it.
- 5mm, 8mm and 10mm Flat: These have no recess and slide over your factory hub lip. The 10mm Flat is not fully hub centric.
- 10mm Hub Centric, check your wheels before ordering: This spacer has a 5mm x 5mm chamfer at the base of its hub lip, where the wheel sits. Your wheel needs at least a 5mm chamfer around the back of its center bore to sit flush. Not all wheels have this.
- 12.5mm Hub Centric, check fitment before ordering: This spacer fits factory hub lips up to 12.5mm. If your hub lip is taller than 12.5mm, this spacer will not sit flush against the hub. It has a smaller 3mm chamfer, which suits most factory and aftermarket wheels.
Some vehicles on this fitment have been reported with hub lips over 13mm, so measure even if you're ordering a thicker spacer.
Modifying the hub: A Hub Centric spacer can only be used on a taller hub lip if the lip is ground or filed down until the spacer sits flush against the hub. This permanently modifies a factory part and is done at your own risk, so we only suggest it if absolutely necessary.
Status Performance Installation Guide
Installation Instructions
Use the guide below to install your wheel spacers. Proper fitment, clean mounting surfaces, correct torque, and correct hardware selection are essential. This guide is our reference for hardware, torque and follow-up checks.
We recommend installation and inspection by a qualified automotive technician, and our warranty requires professional installation, with proof of installation. If you install spacers yourself, follow every check below. If anything doesn't sit flush, stop and contact us.
Incorrect fitment, installation or maintenance can cause wheel separation, loss of control, serious injury or death.
Before You Begin
Always work on a stable surface, support the vehicle securely, and confirm all mounting surfaces are clean before installing.
Critical Fitment Check
If the spacer does not sit fully flush on the hub, or the wheel does not sit flat against the spacer, do not drive on it until the issue is corrected.
After Installation
Re-check torque after about the first 100 km of driving and confirm there is no rubbing, looseness, or vibration. If any occurs, stop using the vehicle and have the installation inspected before continuing.
Torque Chart
Utilize your vehicle's factory torque specification and a torque wrench. Factory specifications should fall within the range below for your thread size. If yours does not, contact us before installing.
| Bolt / Nut Thread | Factory Specification Range |
|---|---|
| 12x1.5 and 12x1.25 | 65 to 100 ft-lbs |
| 14x1.25 | 100 to 120 ft-lbs |
| 14x1.5 | 85 to 155 ft-lbs |
| 1/2-20 | 85 to 115 ft-lbs |
Slip-On Type Spacers
Slip-on spacers require the correct extended wheel bolts and proper seat type for the wheel being installed. Correct thread engagement is critical.
Prep the Hub and Check the Hub Lip
- Lift the vehicle and secure it with jack stands.
- Remove the wheel.
- Thoroughly clean the hub face using a wire brush to remove rust, corrosion, and debris.
- Measure your factory hub lip from the hub face to the end of the lip, ideally with calipers. Hub lip height can vary by axle, so check the front and rear.
- Place the spacer on the hub and test fit for flush contact. On a Hub Centric spacer, the hub lip has to fit fully inside the spacer.
If the spacer rocks or does not sit fully flat, do not install it. Check for burrs, corrosion, debris, or a hub lip that is too tall for the spacer first.
Confirm Bolt Length and Seat Type
- Use conical or ball seat hardware based on your wheel type.
- Measure one OEM wheel bolt from the bottom of the seat to the end of the threads.
- Add your spacer thickness in millimetres to that measurement.
- Select extended bolts using that new length. If it falls between sizes, use the closest readily available length.
- Example: OEM bolt = 28mm, Spacer = 10mm, calculated length = 38mm, so use the closest available length of 40mm.
- Common sizes include 35mm, 40mm, 45mm, and 50mm.
Minimum thread engagement should be 7 full turns for M12 hardware and 8 full turns for M14 hardware. If you have less than that, use longer bolts.
Mount the Spacer and Wheel
- Install the spacer onto the clean hub.
- Check the back of your wheel. It needs enough chamfer around the center bore to clear the spacer's hub lip. Our 10mm Hub Centric spacers need at least a 5mm chamfer, and not all wheels have this.
- Place the wheel over the spacer and ensure the setup remains hub centric and aligned. The wheel must sit flat against the face of the spacer.
- Hand-thread the extended bolts into the hub using the correct seat type.
- Tighten hardware in a star pattern.
- Torque to your vehicle's factory specification (see the torque chart).
- Recheck alignment and flush fit between the hub, spacer, and wheel.
Final Checks
- Spin the wheel by hand and confirm it rotates freely with no rubbing or vibration.
- After driving about 100 km, re-torque all wheel bolts to your vehicle's factory specification, then check them occasionally.
- The extended wheel bolts pass through the spacer and into the hub, so checking the wheel bolts also covers the spacer.
- Stop using the vehicle if unusual vibration, looseness, rubbing or damage occurs, and have the installation inspected before continuing.
Slip-On Hardware Reference
Use these reference graphics to confirm correct bolt length and correct seat type before installing slip-on spacers.
Do Not
- Reuse factory-length bolts with slip-on spacers.
- Install if the spacer does not sit flush or the center bore fit is loose.
- Use mismatched seat styles, such as ball seat hardware on a conical seat wheel.
- Stack spacers.
Bolt-On Type Spacers
Bolt-on spacers mount directly to the vehicle hub using the factory studs and supplied hardware. Proper torque and a flush hub fit are critical.
Prep the Hub
- Lift the vehicle and secure it with jack stands.
- Remove the wheel.
- Thoroughly clean the hub face using a wire brush to remove rust, corrosion, and debris.
- Place the spacer on the hub and test fit for flush contact.
If the spacer rocks or does not sit fully flat, do not install it. Check for burrs, corrosion, debris, or fitment issues first.
Mount the Spacer to the Hub
- Align the bolt holes of the spacer to the vehicle hub.
- Thread the included low-profile nuts onto the vehicle's factory studs.
- Torque each spacer nut to your vehicle's factory specification (see the torque chart), in a star pattern.
- Check whether your factory studs extend past the face of the spacer. This is most likely on thinner spacers such as 15mm. If they do, the wheel may not sit against the spacer.
Do not use impact tools to tighten spacer-to-hub hardware. Overtightening can damage threads or distort the spacer.
Mount the Wheel to the Spacer
- Place the wheel onto the new studs of the spacer. The wheel must sit flat against the face of the spacer, with no contact on the factory studs.
- Hand-thread the wheel lug nuts onto the spacer studs.
- Torque to your vehicle's factory specification (see the torque chart).
- Tighten in a star pattern, then perform a final circular pass.
- If you are using aftermarket wheels, confirm the correct seat type for the hardware.
Final Checks
- Rotate the wheel by hand to confirm there is no rubbing or interference.
- Double check that all hardware is fully seated and torqued.
- After driving about 100 km, re-check torque on both the wheel lug nuts and the spacer-to-hub nuts, then check both occasionally. The wheel has to come off to reach the spacer-to-hub nuts.
- Stop using the vehicle if unusual vibration, looseness, rubbing or damage occurs, and have the installation inspected before continuing.
Bolt-on spacers have two sets of hardware. Check the wheel-to-spacer torque and the spacer-to-hub torque.
Bolt-On Installation Overview
Do Not
- Use impact guns to tighten spacer-to-hub hardware.
- Install if the spacer does not sit flush or the center bore fitment is loose.
- Drive if the wheel is resting on the factory studs instead of sitting flat against the spacer.
- Stack spacers.
Status Performance Delivers
- Hub centric designs that locate on your vehicle's hub
- Built-in stud designs for proper thread engagement
- Designs for trucks, SUVs, and performance builds
- Coverage across Asian, European, and American platforms
- Black hard-anodized finish for corrosion resistance and a clean install look
Need Help Confirming the Right Setup?
Contact us before ordering or installing if you need help with hub bore, spacer thickness, seat type, stud clearance, or hardware selection. A quick fitment check can prevent installation issues later. Contact us here →
These instructions are provided as a general guide. Vehicle specifications, wheel designs, and hardware requirements can vary. Always confirm fitment, hardware, and torque specifications for your exact application before installation. Road-use and inspection requirements vary by jurisdiction, so confirm local requirements before purchasing.
1. Are wheel spacers safe to use, and are they legal?
Wheel spacers can be used safely in suitable applications when correctly selected, installed and maintained. Suitability depends on the vehicle, wheels, spacer thickness and design, mounting hardware, and intended use. Proper installation is essential, but does not make every spacer and wheel combination suitable.
Before installation, confirm compatibility, sufficient thread engagement, full contact between mounting surfaces, and adequate clearance. Follow the installation instructions and torque specifications applicable to your exact setup. We recommend installation and inspection by a qualified automotive technician.
Like other modifications that change wheel offset, spacers can affect handling and loads on wheel bearings and suspension components. Incorrect fitment, installation or maintenance can result in component failure, wheel separation, loss of control, serious injury or death. Stop using the vehicle if unusual vibration, looseness, rubbing or damage occurs, and have the installation inspected before continuing.
Road-use legality is a separate consideration. Requirements vary by province, territory and other jurisdictions, and some inspection standards reject aftermarket wheel spacers even when correctly installed. We do not guarantee road-use legality or inspection approval for every application. Before purchasing, confirm the requirements where your vehicle will be registered and operated.
Review our installation guide, and contact us if you need help identifying the appropriate product.
2. How do I choose the correct size of wheel spacers for my vehicle?
To select the right size: (example for a 2007 Nissan 350Z)
- Measure your bolt pattern (e.g., 5x114.3).
- Check the hub bore size, to ensure it’s hub-centric (e.g., 66.1 mm).
- Determine the thickness (20mm) needed by measuring the gap between your wheel and fender for the desired clearance.
If unsure, consult your vehicle manual or seek advice from a specialist. Most brands also provide guides for specific vehicle makes and models. - Also make sure to match the thread pitch (e.g., 12x1.25).
3. Will wheel spacers affect my vehicle's performance or handling?
Yes. Spacers widen the track width and change the wheels' effective offset, which can affect steering characteristics, handling and loads on wheel bearings and suspension components. Thicker spacers and combinations with larger tires, different wheels or other suspension modifications should be assessed before installation.
4. Do wheel spacers require longer wheel studs or special hardware?
In some cases, yes. If your spacer thickness exceeds the length of your factory studs, you’ll need extended wheel studs or bolt-on spacers that have their own studs. Vehicles that use wheel bolts need extended wheel bolts with slip-on spacers. Check thread engagement using the requirements in our installation guide.
5. Can wheel spacers cause vibration or damage?
Yes, they can. Vibration often occurs if a spacer isn't hub-centric (where the spacer centers on the hub) or if the hardware isn't torqued properly. Incorrect fitment, installation or maintenance can also damage components. Follow the torque and follow-up checks in our installation guide. Stop using the vehicle if unusual vibration, looseness, rubbing or damage occurs, and have the installation inspected before continuing.
6. Are wheel spacers reversible or removable?
Yes, wheel spacers are removable. They do not cause permanent modifications to your vehicle, provided they are installed correctly. Clean the hub and spacer surfaces at installation to help prevent corrosion between them.
7. What materials are your wheel spacers made of?
Status Performance wheel spacers and adapters are machined from T6-6061 billet aluminum, which is lightweight and resists corrosion. The included mounting hardware and wheel bolts are steel.
8. Will wheel spacers make my wheels stick out too far?
The amount your wheels stick out depends on the thickness of the spacers. To avoid making your wheels extend excessively, measure the distance from your wheel face to the edge of the fender and choose a spacer thickness that fits within that range. Tire coverage and vehicle width requirements vary by jurisdiction, so confirm them where your vehicle is registered and operated.
9. Are wheel spacers compatible with aftermarket wheels?
Yes, wheel spacers can work with aftermarket wheels as long as the bolt pattern, hub bore, and spacer thickness are compatible with your setup. Some aftermarket wheels might require spacers to achieve proper clearance from brake calipers or suspension components. Check the back of the wheel too, because some Hub Centric spacers need a minimum chamfer around the wheel's center bore for the wheel to sit flush.
10. Do I need professional installation for wheel spacers?
We recommend installation and inspection by a qualified automotive technician, and our warranty requires professional installation, with proof of installation. A professional can confirm correct fitment and torque, and can spot issues such as improper thread engagement or interference with other components.
If you install spacers yourself, use a torque wrench and follow our installation guide. Pay particular attention to these checks:
- The spacer must sit flush against the hub. A hub lip that's too tall can stop it from sitting flush.
- The wheel must sit flat against the face of the spacer. Factory studs that extend past the spacer can stop it from doing so.
- If either one doesn't sit flush, do not drive on it. Contact us if you need help.
11. What is a hub lip, and why does it matter?
The hub lip is the raised ring at the center of your vehicle's hub. It has to fit inside a Hub Centric spacer so the spacer can sit flush against the hub. Hub lip height varies by make, model, year and axle, so measure the front and rear from the hub face to the end of the lip, ideally with calipers. If a spacer doesn't sit flush, do not install it. Our 72.56, 66.6 and 57.1 spacer pages include a Hub Lip Guide.
12. What's the difference between a Flat and a Hub Centric spacer?
A Hub Centric spacer has a recess that fits over your factory hub lip, plus its own hub lip on the wheel side for the wheel to center on. A Flat spacer has no recess or wheel-side lip. Its bore still matches your hub and it slides over the factory lip, but it doesn't extend the lip, so less of the factory lip is left to center the wheel. Our 5mm and 8mm spacers are Flat, and we offer the 10mm in both styles.
13. What's the difference between wheel bolts and studs?
Wheel bolts thread into the hub, and are common on BMW, Audi, Mercedes, VW and Porsche. A slip-on spacer on these vehicles needs longer wheel bolts with the correct thread pitch and seat type (conical or ball). Studs stay fixed to the hub with lug nuts holding the wheel on, and are common on Japanese, Korean and North American vehicles. A bolt-on spacer on these vehicles mounts to your factory studs using the included acorn nuts, and your wheel then mounts to the spacer using your existing lug nuts.